Caldigit S2VR HD Manual Bedienungsanleitung

S2VR HD 5 Bay SATA 3Gb RAID Solution Performance, Protected, JBOD User Manual CalDigit, Inc. 1941 Miraloma Ave, Unit

9 Installing the Hard Drive Tray Modules Note: Your S2VR HD is shipped with the drive modules packaged separately to prevent them from damage.

10 Go to “Management Tab” setup password, Voice & E-mail notification  Password (Changing the Password) 1. Select Change Password fro

11 Configure RAID Level Note: Your S2VR HD is configured by CalDigit initially in JBOD mode. You can modify your RAID LEVEL by reconfiguring y

124. Click IGNORE when the Disk Insertion message comes up. 5. Go to OS Disk Utility OS/HD/APP/UTILITY/DISKVERIFY 6. Select S2VR Drives 7. Cre

13 Advanced RAID Configuration 1. Select S2VR (Box with serial #) 2. CLICK on Configure RAID 3. CLICK on Advanced tab

14 TURBO Feature You can choose from 30 – 100% of the hard drive capacity, to remain at the desired performance level. Important Note: As is

15Important Note: You must delete your S2CR RAID set on the disk utility whenever you are configuring your S2VR into a new setting. If you do no

161. Open S2VR Manager, Select JBOD mode & follow prompts to format your S2VR to JBOD mode. 2. The Following system messages will appear

174. Create a partition for each hard drive on your S2VR 5. After you initialize, this is what you should see. Informational Factoid:

187. Click on the RAID Button on the Disk Utility. 8. Drag every S2VR drive into the list box to create set. Input the desire RAID set nam

1Table of Contents Introduction ………………………………………………………………………………………………. 2 Features and benefits of the S2VR HD ………………………………………………………………… 2

1911. The RAID Set name window will again appear, CLICK Create button on lower right corner of window. 12. Restart your computer, and your new

20  JBOD to Performance Mode Your data will be lost as this process will reformat your drives. Backing up your data on another S2VR HD is hig

212. After you change your S2VR’s setting into Performance mode, you S2VR Manager will show the information, as below. 3. Create Partition v

224. Restart your computer, and your newly configured S2VR is ready to use!  JBOD to Protected Mode Your data will be lost as this process

231. Open S2VR Manager, Select Protected mode & follow prompts to format your S2VR to Protected mode. 2. After you change your S2VR’s set

243. Launch the Disk Utility; create partition for the hard drives on your S2VR. 4. Click on the RAID Button on the Disk Utility. 5. Drag ev

257. Restart your computer, and your newly configured S2VR is ready to use!  Protected Mode, rebuild information Protected mode combines the

26 Demonstration of HDD failure 1. Your S2VR manager will monitor your S2VR HD and will notify you in the event of a problem.

27 Troubleshooting In the event that your S2VR HD is not working correctly, please refer to the 3 items below to find out where the

28 Serviceability The S2VR HD is designed to provide easy disk drive replacement, should a disk drive module need to be serviced, simply unscr

2  Introduction Thank you for purchasing your CalDigit S2VR HD. CalDigit was established in North Orange County, California, with a team o

3 Opening the Box Remove all components from the shipping container. Retain all boxes and packaging materials, in the event that you have

4  Hardware Requirements • PC or Mac with an available PCI-e or PCI-x slot 500 Mhz or faster** • CD-ROM drive • 1GB of RAM minimum **Not

5 5. Select your OS hard drive as the Destination. 6. Next, CLICK Install. 7. Finishing Installation, CLICK Continue. Informational F

68. Installation complete, CLICK CLOSE.  Verify System Profiler Check to make sure that the card has been installed under System Profiler.

7 Install S2VR Manager 1. Double CLICK the application on the provided CD, CalDigit S2VR v1.03. 2. Introduction, CLICK Continue.

84. Installation Successful, CLICK Close. 5. Find the S2VR Manager. Directory: OS drive > Applications > Utilities > CalDig